Skip to main content

Set up General Settings for Work Orders

Eptura Knowledge Center

Set up General Settings for Work Orders

                      Level: Administrator

All changes to your Work Order Settings will impact ALL users.

  1. Navigate to  Settings.
  2. Under the Module Settings heading, click Work Orders.  The Work Order Settings screen displays.

clipboard_ef2f1a90b3ab3dd0f2281e1bd085b17d5.png

The General tab displays by default, and this contains:

General Settings


The General Settings include:

Setting Description

Next WO# spin box 

Enter or select the next work order number.  Subsequent work order numbers will increase by 1. 

For example, 200020 and then this will increase the number from this starting number.

Overhead Part Markup spin box

The marks up your part on on your work order to account for overhead expenses.

Enter or select the mark-up percentage (%).

This does not affect your invoice price points or markups.

Autolink Parts to Assets toggle

Either toggle:

  • ON - we recommend this setting is turned on as it automatically links the parts used on work orders to the asset that was worked on. This automatically creates an accurate part list for your asset.
  • OFF
Set Inventory Consumed to Completed Date toggle

Either toggle:

  • ON - we recommend this setting is turned on as it sets the consumed date of parts used on work orders to the work order's completed date.  
  • OFF - sets the consumed date to the day you listed the part on the work order
Schedules Due At spin box

Set the percentage and this determines when your PM schedules are due. 

For example, if you set this to 90%, the system will indicate early that it's time to turn your PMs into work orders, when they pass the 90% mark. 

Post Budget Transaction On drop-down

Determine when you would like budget expenses to be recorded.  Select from:

  • Date Completed - this is the recommended, default setting.
  • Date At Time Posted - this is used only if your organization has a policy against backlogging expenses.
Post Re-Posted Budget Transaction drop-down

If you reopen a work order, the recorded transaction is reversed.  This let's you decide when the reposted transaction is dated. Select from: 

  • Date Completed - this is the recommended, default setting.
  • Date of Time Posted  - this is used only if your organization has a policy against backlogging expenses.
Default Work Type drop-down New, unscheduled work orders will start with this work type (does not apply to scheduled PMs, which have their work type pre-set).
Assign Vendor toggle

This let's you assign vendors to a work order.

Either toggle:

  • ON
  • OFF

Lookups


  The following lookups can be set up:

  • Other Cost Types:  Establish your choice of line-item expense options, that can appear on a work order.  

Work Orders and Purchase Orders share this library.

  • Failure Codes:  Sets the options that will appear, on Work Types that have the Failure Mode turned on, see Work Type section below, for more details.

Require Reset Logs for PM's and Component/Tire Installations


This allows you to set a requirement for meter/logs being entered on a timely basis.  For example:  If you set Days since last entry to 7, and it has been 10 days since the last hour meter reading on your forklift, any work order created for that asset will require you to update the hour meter before you can complete it.   If it has been less than the days set here, the work order will not force you to include a meter reading.  

There are three system-generated Data Confidence Levels that the system can display:

clipboard_ea9029ff2d664c294d5968bd934e05130.png

Good

0-9 Days

clipboard_e6c79080e35a4d1475d1f9575347a0d94.png

Fair

10-30 Days

clipboard_e4cc4091e9a6b6764443baec91bd7be12.png

Bad

31+ Days

Impact on Tech's completing Work Orders

If the tech enters a current meter reading while doing the Work Order then: 

  • Continue as usual and no message will pop up when you complete the Work Order.   

If NO meter reading is entered on the Work Order then:     

  • If completed within the number of days established on your data confidence level, no message will pop up when you complete the Work Order as usual. 
  • If completed AFTER the number of days established on your data confidence level, an error message will make it clear which specific Meter/Log entry is required
Eptura Asset Example Work Companion Mobile App Examples
c51dcc13-4769-4a48-aa3b-226b3d32fe23.png WC warning - logs needed.png               Meter needed - hours.png