Skip to main content


Eptura Knowledge Center

Technical details


Technical specification for Condeco v3 Desk Booking Screens

Feature Description
Dimensions (width x height x depth) 85×68.5×10mm / 3.34×2.69×0.39”
Operating system Android 8
Display 3” LCD with CTP
Processor i.MX7 processor
Memory 1Gbyte DDR3
Storage 8Gbyte eMMC
Wireless network Wi-Fi 802.11 b/g/n/ac dual-band, 2.4 GHz and 5 GHz
Required signal strength (RSSI): -60dBm or better
Bluetooth v4.1
RFID/NFC 125KHz and 13.56MHz
USB USB Type C connector
RGB RGB indicator LEDs
Maximum operating temperature 40 Degree Celsius

v3 Desk Booking Screen power supply

Condeco v3 desk booking screens are powered by 5V USB with a peak power consumption of 0.66A (3.3 watts) during boot-up. Normal power consumption is 0.34A (1.7 watts) rising to 0.53A (2.65 watts) when in use.

Power supply Range
Voltage 5V +/- 0.25V
Current 0.334-0.66A
Power consumption 1.7-3.3W

Note that the desk booking screens require more than 0.5A to boot up but will run on less during normal operation.

USB C cable

The device is supplied with a 2m USB-C cable.

USB-C cable (supplied)

Power options

Power blocks/hubs and USB adapters are not supplied by Condeco.

You can use a 3rd-party USB-C charger block/hub to power more than one device from a single power source.

Two port USB-C power block (not supplied)

USB-C charger blocks typically have a maximum of two ports. If you have many desk booking screens arranged in a bank, you can use a 3rd-party multi-port USB-A hub combined with a USB-C to USB-A adapter for each desk booking screen.

USB-C to USB-A adapter (not supplied)

Multiport USB-A power blocks (not supplied)


The Condeco desk booking screens support Wi-Fi 802.11 b/g/n/ac dual-band, 2.4 GHz and 5 GHz.

The operation of the desk booking screens without Internet access is not supported.

The desk booking screens are managed through a cloud service and need internet access before they can be activated and for their continued operation. The same is true even if Condeco Workspace Booking is deployed on-premise.


If you use allowlists or denylists you must allow access to the fully qualified domains listed in the domain allowlist. Learn more about the domain allowlists


The screens support SSIDs authentication with WPA2-PSK security or no password SSIDs. PEAP is supported by desk booking screens on v8.1.39 or later.

Wi-Fi Network Deployment

Condeco do not supply any Wi-Fi infrastructure or access points. Connectivity for the devices must be available and managed by the relevant customer teams.

Dedicated SSID

Customers can create a new dedicated SSID or use an existing Wi-Fi SSID with a WPA2-PSK password. This network will only require access to the Condeco Workspace Booking solution and to some cloud endpoints, so the SSID can be segregated on a VLAN if required.

Guest Wi-Fi with MAC Authentication Bypass

The screens can be supplied with documented MAC addresses which can be used to authorize the devices on OPEN guest Wi-Fi networks. The devices cannot authenticate to web-page based guest Wi-Fi solutions.

RFID Technology and the Condeco v3 Desk Booking Screen

RFID (Radio Frequency Identification) technology allows the user to book the desk with their RFID card. The operation frequencies are 125 kHz and 13.56 MHz

  • 125 kHz used for HID Prox card.
  • 13.56 MHz used for Mifare ISO 14443 and HID iClass cards ISO 15693.

Compatible RFID cards

The following RFID cards are compatible with the Condeco v3 Desk Booking Screen:

  • HID Prox
  • HID iClass
  • Mifare
  • Desfire

NFC (Near-Field Communication) technology

NFC is used by the v3 desk booking screen for transferring configuration data from the Condeco Android setup application.